在线观看导航 I 永久黄网站色视频免费观看w I 亚洲狼人色 I 热热热av I 精品无人区无码乱码毛片国产 I japan丰满妇hd肉感 I 国内露脸中年夫妇交换 I 四虎av网址 I 亚洲精品国产免费 I 国产三级自拍视频 I 中文字幕亚洲综合久久 I 午夜不卡在线观看 I 久久久久99精品成人片我成大片 I 国产香蕉视频在线观看 I 欧洲视频在线观看 I 顶级毛茸茸aaahd极品 I 九色porny在线视频 I 男男互c开荤粗肉尿在里面视频 I 日本免费观看网站 I 一区精品在线观看 I 手机在线电影av I av品善网 I 国产精品免费久久久久久 I 成人激情午夜 I 午夜精彩视频在线观看 I 免费黄色免费 I 影音先锋男人色 I 少妇白嫩娇喘 I 99热国内精品永久免费观看 I 亚洲熟妇av一区二区三区下载 I 亚洲区成人777777精品 I 国产精品对白刺激在线观看 I 亚洲国产成人精品无码区蜜柚 I 日韩精品 在线 国产 丝袜 I 色多多视频导航 I 69国产成人综合久久精品 I 337p日本欧洲亚洲大胆人人 I 玖玖色在线视频 I 国内精品一区二区福利视频

The reason for the insufficient suction of stone sucker, I will introduce to you. Because the heat capacity of semiconductor rectifier element is very small, when the rectifier is overloaded, the temperature of the element rises sharply and the diode is burned. Rectifier components will be aging, there will be a degenerative phenomenon, resulting in the output of the electric bed, so that the suction of the vacuum sucker is insufficient. The inductance of the force line device by dry vacuum suction cup is very large, which will produce a large overvoltage at the moment of disconnecting the coil and may break down the rectifier element. The gas consumption of the straight air generator is determined by the diameter of the working nozzle, but it is also related to the working pressure. With the same nozzle diameter, the air consumption increases with the increase of working pressure. The diameter of nozzle is the main basis for selecting vacuum generator. The larger the nozzle diameter, the larger the suction flow and gas consumption, and the lower the vacuum degree: the smaller the nozzle diameter, the smaller the suction flow and gas consumption, but the higher the vacuum degree. To change the tube base, first unscrew the 2 screws (with gaskets) on the side of the manifold base, replace the old manifold base with a new one, and then put the gasket on the screw, pay attention to the screw with equal force.

In vacuum sensor, turn off the vacuum sensor on the side of 2 screws, and remove the vacuum sensor, then twist off vacuum sensor below the four screws (with washer), and then changed into a new vacuum sensor and put on the washer screw on the base of screw, will be in a good vacuum sensor installation back in vacuum, on the last point on the surface of the upper screw again: in silencer, First screw off the straight empty generator surface, remove the muffler, there is a relay pipe connection in the middle, and then remove the muffler below the 2 black nails, replace the old muffler with the new, screw the muffler base screw, install the relay pipe in the middle, and then reinstall the muffler, and then screw on the side screw.